how to clean bath toys with holes
For squeezable toys follow the same instructions as if you were using bleach. If they still smell like vinegar just do a simple water rinse and dry completely before.
32 Things You Should Be Cleaning But Aren T Cleaning Bath Toys Cleaning Hacks Diy Cleaning Products
Do the same with clean water to.
. Its also worth investing in a net bag that can be hung above the bath to keep the toys well away from water when theyre not being used. To stop water getting in clean each toy and allow to dry then use a splodge of hot glue or water-proof silicon to seal the hole at their base. Mix 1 cup of white vinegar with 2 gallons of water and let toys soak for an hour.
Add 1 cup of vinegar for every gallon of freshly boiled water in a basin or sink. Vinegar is an acceptable substitute for cleaning bath toys. Fizz for the cleaning whiz.
Sterilize bottles in boiling water or the microwave. The dishwasher runs at high temperatures in order to destroy any bacteria so always check the label on the toy s to make sure it is dishwasher safe before using this method. Allow the toys to soak for about an hour.
When done the toy should not smell like anything at all well aside from the smell of the latex rubber. Fill the tub with 3 to 4 inches of water add a cup of vinegar and soak for about 30 minutes before rinsing. Set them along the side of the tub or somewhere else where they can dry quickly.
Check that the toy s can be safely washed in the dishwasher. Squeeze out the rubber ducks and hang bath. Plug up the holes Use a hot glue gun carefully craft glue school glue or even super glue to close the water-squirting holes.
You can make a solution by mixing one gallon of water with ½ cup of white vinegar and soaking the toys in it for about an hour. After making sure all the water is out let the toys dry. Repeat again in hot as you can tolerate plain water.
Squeeze it quite a few times. I used regular detergent and a rinse cycle with white vinegar. If the inside of the toy is moldy squeeze up the vinegar water shake the toy then squirt the water out.
Turn on the bathroom exhaust fan for 15 to 20 minutes after bath time to draw humidity out of the room and help the toys dry even faster. To clean bath toys with holes soak the toy in your chosen solution and squeeze whilst its submerged. After each bath squeeze as much water out of the toys as possible.
Force the toys to suck in the solution and squirt it back out several times. Bring the toy out of the water and squeeze again to empty the holes. Hydrogen peroxide 3 is non-toxic anti-bacterial anti-fungal and anti-mould.
Which glue works best will depend on the material the toy is made of and the size of the hole. The first way is simply to throw them in the dishwasher. After theyre done soaking scrub any stubborn spots with a brush and soap.
Submerge the toy in a 70 solution of rubbing alcohol. Placing some towels in the machine with the toys will help keep them from banging around too much and from making too much noise. Hot and even steam might be a better option but I wanted to be sure not to.
Take a clean sponge and scrub the outside of the toys with the vinegar water. The good news is theres a whole lot that parents can do to minimize mold and bacterial growth. It probably wont get rid of all the mold but it does an ok job.
The most prominent place for mold to grow is inside bath toys. Then scrub the toys to clean off the mold and then let them air dry. This could prevent water from getting inside the toy.
Squeeze out as much water as possible particularly from squeezy toys then leave them to dry. Put a pot of boiling water on the stove and sit the toys in it for 10 20 minutes. I used a quick wash on cold extra heavy medium spin cycle and fan dry.
Thisll suck the solution into the holes. The second way is to boil the toys. Repeat this process in hot as you can tolerate soapy water.
Avoid using water squirting toys enough said. Squeeze out the excess water inside the toys and let them dry out. Thoroughly squeeze out all the liquid you can.
Humidity can be an issue too so switch the bathroom fan on for 20 minutes to draw moisture out of the room. Or better still plug the hole before new toys make their bath debut. You will still need to scrub them to remove some of the gunk.
Bath Toys That Don T Mold Kids Bath Toys Baby Bath Toys Best Bath Toys
How To Clean Bath Toys 5 Genius Hacks To Make It Easy Cleaning Bath Toys Bath Toys Diy Toy Storage
How To Clean Bath Toys Cleaning Bath Toys Bath Toys Baby Bath Toys
Close Up The Holes On The Bottom Of Bath Toys With A Little Bit Of Hot Glue To Keep Them From Getting Moldy Fun To Be One Bath Toys Tub Toys
Cleaning Bath Toys Cleaning Bath Toys Tub Toys Bath Toys Mold
Pin On Cute Kids Stuff
Pin Van Alvaro Uribe Design Op Baby And Design Badspeelgoed Speelgoed Voor In Bad Speelgoed
How Why To Clean Bath Toys Cleaning Bath Toys Bath Toys Cleaning Toys
Glue The Holes In Bath Toys So Water Doesn T Get Inside And Produce Mold Smart Cleaning Bath Toys Bath Toys New Baby Products
Bath Toys That Don T Mold Bath Toys For Toddlers Bath Toys Baby Bath Toys
Amazon Com Yookidoo Flow N Fill Spout Bath Toy 9m Bathtub Toys Baby Baby Bath Toys Cool Baby Stuff Baby Bath
2 Surefire Ways To Disinfect Clean Bath Toys Cleaning Bath Toys Baby Bath Toys Bath Toys
Oli And Carol Elvis The Duck Bath Toy Bath Toys Soft Pastel Carole
Oli And Carol Elvis The Duck Bath Toy Bath Toys Soft Pastel Carole
Moldy Bath Toys Here S How To Clean Em Via Purewow Bath Toys Mold Kids Bath Toys Cleaning Bath Toys
How To Clean Bath Toys Cleaning Bath Toys Kids Bath Toys Diy Toys
Yucky Ducky The Girl In The Red Shoes Baby Bath Toys Cleaning Bath Toys Bath Toys
Keeping Kids Bath Toys Clean And Mold Free Kids Bath Toys Kids Bath Bath Toys
How To Clean Bath Toys Baby Bath Toys Kids Bath Toys Cleaning Bath Toys